VEVOR 26 in Hairpin Table Legs, Set of 4, 3 Rods, Black Steel
$25.90Wholesale price, no minimum order
Key Features
Height
Three-rod build
Load
Mounting plate
Finish
In stock
Quick Answer
This is a set of four 26-inch black hairpin table legs made from three 3/8-inch steel rods, rated at 220 lb per leg. The mounting plate is 4 mm thick, the tube is 10 mm across, and the box includes rubber floor pads and self-tapping screws. The tabletop is not included.
Description
At a Glance
Set of four 26 in black hairpin table legs in 3/8 in steel, 220 lb per leg and an 880 lb nominal set rating. 4 mm plate, rubber feet and screws included. Top not included.
26 Inch Black Hairpin Table Legs, Set of 4
Hairpin legs are simple to fit and hard to get right: the height has to match the top, and the leg has to stay stiff under a loaded table. This set of four 26-inch legs uses three 3/8-inch steel rods per leg, a 4 mm mounting plate and a black powder-coat finish. They suit a console table or a compact desk.
The tabletop is not included. This is a set of four legs with mounting hardware and floor pads. You supply the top and the fasteners that suit its material.
Finished height
Leg height is measured before the top goes on. With a 1 in top, the finished height is about 27 in; with a 1.5 in top, about 27.5 in. Measure the chair, stool or counter the table will be used with, then choose the leg that lands on that number.
- Leg height: 26 in / 66 cm
- Finished height with a 1 in top: about 27 in
- Finished height with a 1.5 in top: about 27.5 in
Three rods, not two
Each leg is built from three 3/8 in (9.5 mm) steel rods. The third rod stiffens the hairpin and spreads the load across the mounting plate, which matters on a dining table or a bench that gets leaned on. The tube diameter is 0.39 in (10 mm).
The mounting plate is 4 mm thick, with pre-drilled holes. A thicker plate resists bending where the leg meets the top, which is the joint that usually fails first on a cheap set.
What the load rating means
Each leg is rated at 220 lb, and the set is listed at 880 lb with four legs. That set figure assumes the weight is spread evenly and the tabletop does not flex. A thin top, short screws, a heavy load on one corner or a table used as a step can fail well below the leg rating.
Keep the load centred, use fasteners long enough to bite into solid material, and check the table for wobble before putting weight on it. A cross brace or apron helps on long, narrow benches.
Mounting
- Turn the top face down on a protected surface.
- Set the four legs in place with equal overhang. Mark the holes through the mounting plate.
- Drill pilot holes sized for your screws. Do not drive screws into the end grain of a particle board top.
- Fix each plate with all its screws, then stand the table on a level floor and check for rocking.
- Fit the rubber floor pads and adjust the position of the legs if the table is not stable.
Floors and finishes
The black powder coat is a durable factory finish, but it can chip if a leg is dragged across concrete. The rubber pads in the box separate the steel from wood and tile floors and reduce movement. Wipe the legs with a damp cloth; avoid abrasive pads.
Ordering
One set, wholesale pricing. The listed price is our wholesale rate for one set of four legs. There is no minimum order quantity and no separate tier price, so one set and several sets cost the same per set.
Performance & Applications
Specifications
| Brand | VEVOR |
| Amount | 4 PCs |
| Table Leg Height | 26" / 66 cm |
| Material | Carbon Steel |
| Tube Thickness | 0.0473" / 1.2 mm |
| Tube Diameter | 0.39" / 10 mm |
| Load Capacity(Each) | 220 lbs / 100 kg |
Be the first to review “VEVOR 26 in Hairpin Table Legs, Set of 4, 3 Rods, Black Steel”
Frequently Asked Questions
Q: Is the tabletop included?
A: No. The listing is four legs with mounting screws and rubber floor pads. The top is supplied by the buyer.
Q: What finished height will 26 in legs give?
A: Add the thickness of your top. With a 1 in top the table finishes about 27 in high; with a 1.5 in top it finishes about 27.5 in.
Q: How much weight will the set hold?
A: Each leg is rated at 220 lb and the set is listed at 880 lb with four legs. That assumes an even load, a stiff top and sound fasteners. Leave headroom for benches and tables that get leaned on.
Q: Are screws included?
A: Yes. Self-tapping screws and four rubber floor pads are included. Check that the screw length suits the thickness of your top.
Q: Will the legs scratch a wood floor?
A: The rubber pads in the box sit between the steel and the floor. Fit them before the table is used and replace them if they wear through.
Q: Can I cut the legs shorter?
A: The legs are powder-coated steel and can be cut, but cutting exposes bare metal and changes the angle of the foot. It is easier to order the height you need.
Q: What is the difference between the 28, 30 and 34 inch legs?
A: 28 in suits a dining table or desk, 30 in suits a dining table or a desk with a thin top, and 34 in suits a counter-height table or standing surface.
Q: Do the legs fit a round table?
A: Yes. Set them in a square or slightly inset pattern under the top. The mounting plates need a flat area wide enough for all four holes.
Q: How do I stop the table from wobbling?
A: Check that the top is flat, the plates are fully screwed down and the floor is level. A thin top may need an apron or brace to stop it flexing between the legs.
Questions & Answers
Related products
-
VEVOR 16 in Hairpin Table Legs, Set of 4, 3 Rods, Black Steel
Original price was: $23.90.$20.32Current price is: $20.32.
Top Rated in Furniture
-
VEVOR 16 in Hairpin Table Legs, Set of 4, 3 Rods, Black Steel
Original price was: $23.90.$20.32Current price is: $20.32.
0 reviews for VEVOR 26 in Hairpin Table Legs, Set of 4, 3 Rods, Black Steel
Customer reviews
No reviews found